Average Force of Deployment and Maximum Arrest Force of Energy Absorbers Lanyards
Por favor, use este identificador para citar o enlazar este ítem:
http://hdl.handle.net/10045/109858
Título: | Average Force of Deployment and Maximum Arrest Force of Energy Absorbers Lanyards |
---|---|
Autor/es: | Carrión Jackson, Elena | Saez, Pedro Ignacio | Pomares Torres, Juan Carlos | González Sánchez, Antonio |
Grupo/s de investigación o GITE: | Grupo de Ensayo, Simulación y Modelización de Estructuras (GRESMES) |
Centro, Departamento o Servicio: | Universidad de Alicante. Departamento de Ingeniería Civil |
Palabras clave: | Energy absorber lanyard | Fall arrest systems | Dynamic performance test | Arrest force |
Área/s de conocimiento: | Mecánica de Medios Continuos y Teoría de Estructuras |
Fecha de publicación: | 20-oct-2020 |
Editor: | MDPI |
Cita bibliográfica: | Carrión EÁ, Saez PI, Pomares JC, Gonzalez A. Average Force of Deployment and Maximum Arrest Force of Energy Absorbers Lanyards. International Journal of Environmental Research and Public Health. 2020; 17(20):7647. https://doi.org/10.3390/ijerph17207647 |
Resumen: | Energy-absorbing lanyards (EAL) are part of fall arrest systems (FAS), their main mission is to dissipate the energy generated during the fall, ensuring that the arresting force does not cause injury to the user. For the design of FAS as set out in the American standard Z359.6 and the Canadian Z259.16 it is essential to know the deployment force or average arrest force (Fa). Fa is necessary to estimate the elongation that the absorber will suffer during the fall and therefore essential data to calculate the clearance distance. There is a lack of useful experimental data for the design of this personal protective equipment (PPE). This work provides empirical data required for the design of FAS with EAL in accordance with EN 355. This paper covers different types of EAL that are marketed internationally; different empirical data, average and maximum forces, required for improving safety design are researched. Six manufacturers, 10 models, and 2 samples of each model were selected, with total of 20 tests being performed. Dynamic performance tests were carried out, the free fall of a person was simulated using a 100 kg steel ballast from the maximum height allowed by the equipment, obtaining the maximum arrest force (Fm), average deployment force (Fa), and, by calculating the balance of forces, the maximum and average acceleration suffered by the ballast during its arrest. In light of the results, relevant conclusions for user safety are obtained. It is feasible to raise the safety requirements established by the different standards. The Fm can be established below 6 kN in the EAL, and the Fa can be estimated at 87.5% of the Fm. The categorization of the force–time curve in fall arrest with EAL has been obtained. Two EAL purchased on the market exceed the Fm permitted, therefore it is recommended to increase the quality controls of EAL. |
URI: | http://hdl.handle.net/10045/109858 |
ISSN: | 1661-7827 (Print) | 1660-4601 (Online) |
DOI: | 10.3390/ijerph17207647 |
Idioma: | eng |
Tipo: | info:eu-repo/semantics/article |
Derechos: | © 2020 by the authors. Licensee MDPI, Basel, Switzerland. This article is an open access article distributed under the terms and conditions of the Creative Commons Attribution (CC BY) license (http://creativecommons.org/licenses/by/4.0/). |
Revisión científica: | si |
Versión del editor: | https://doi.org/10.3390/ijerph17207647 |
Aparece en las colecciones: | INV - BIMAEC - Artículos de Revistas INV - GRESMES - Artículos de Revistas |
Archivos en este ítem:
Archivo | Descripción | Tamaño | Formato | |
---|---|---|---|---|
Carrion_etal_2020_IntJEnvironResPublicHealth.pdf | 4,03 MB | Adobe PDF | Abrir Vista previa | |
Este ítem está licenciado bajo Licencia Creative Commons